- Eltek flatpack 2 installation manual install#
- Eltek flatpack 2 installation manual manual#
- Eltek flatpack 2 installation manual Pc#
The rectifier works in stand-alone mode or in parallel with other rectifiers, then communicating via CAN bus with the system’s Smartpack controller and other connected rectifiers. The module is designed for battery charging and supplying of high quality DC power to telecom equipment and similar applications. Flatpack2 Rectifier The Flatpack2 rectifier module is a hot-pluggable, digitally controlled switch mode power supply. are typically also a part of the system.Ģ. The system is fed from an external AC mains supply, and consists of rectifiers in power shelves, a control unit and DC distribution unit. Alarm Outputs NC-C-NO Digital Inputsįlatpack2 rectifiers LVLD Telecom equipmentĭC Supply (24V, 48V or 60V*) *Available from 2007įigure 1 Example of a typical Flatpack2 PS system for DC power supply of telecom equipment. The PowerSuite application enables you to configure and operate system from a personal computer. The Smartpack controller monitors and controls the whole system, and serves as the local user interface between you and the system. System Diagram ⎯ Flatpack2 DC Power System The Flatpack2 rectifier modules are the building blocks of Flatpack2 PS systems, see Figure 1. Read also the generic and site specific documentation that was delivered with your Flatpack2 DC power system. The booklet also presents the rectifier’s technical specifications, such as input voltage range, output power, operating temperature range, etc.
Eltek flatpack 2 installation manual install#
Welcome The Flatpack2 rectifier module is a powerful and cost-effective power supply used in Eltek’s Flatpack2 DC power system.Ībout this Guide This booklet provides users of Flatpack2 DC power systems with the required information to install and operate the Flatpack2 rectifier modules. 10 Specifications Flatpack2 Rectifier 24V, 2000W. 9 Specifications Flatpack2 Rectifier 48V, 2000W. Specifications Flatpack2 Rectifier 48V, 1800W. 7 Correct Rectifier Position in Power Shelves. 6Ĭonnections.7 CAN Bus Addressing (plug-and-play). 4 System Diagram ⎯ Flatpack2 DC Power System.
Eltek flatpack 2 installation manual manual#
Installation is to be in accordance with the recommendations herein Please read the manual carefully before using the equipmentĪbout this Guide. As the modules incorporate large charged capacitors, it is dangerous to work inside the system even if the mains supply is disconnected Products into which our components are incorporated have to comply with a number of requirements. Safety Precautions The equipment described in this manual must only be operated by Eltek Energy personnel or by persons who have attended a suitable Eltek Energy training course The equipment represents an energy hazard and failure to observe this could cause terminal injury and invalidate our warranty There are hazardous voltages inside the power system. No part of this document may be reproduced or transmitted in any form or by any means - electronic or mechanical, including photocopying and recording - for any purpose without the explicit written permission of Eltek Energy. Requirements for the Eltek -48 Volt DC Flatpack2 systems.1 Welcome Information in this document is subject to change without notice and does not represent a commitment on the part of Eltek Energy. This Installation and Commissioning Manual provides simple instructions as to the installation 63 28.2 USING SMARTSUITE: A START UP GUIDE.
Eltek flatpack 2 installation manual Pc#
63 SETTING UP COMMUNICATION BETWEEN PC AND SMARTPACK. 60Ģ8.1 INSTALLATION OF SMART SUITE SOFTWARE. SYSTEM COMPONENTS MINIMUM OPERATING LIFE. 40 17.3 FRONT KEYPAD MENU TREE FOR SMARTPACK CONTROLLER. INSTALLING AND REMOVING THE SMARTPACK CONTROLLER (ETHERNET CONNECTION).
33 15.4 REPLACING AND INSTALLING RECTIFIER MODULES. 33 15.3 IDENTIFICATION OF DIFFERENT RATED RECTIFIERS. INSTALLATION AND OPERATION OF RECTIFIER MODULES. INSTALATION & REFRESHING VOLTAGES OF BATTERIES. EXPANSION RACK CONNECTION AND ADDING BATTERY STRINGS. This manual is in process of revision if you require updated manual please contact withĮltek Australia Pty Ltd ACN072 645 446 ABN 90 072 645 446Į-Mail (Sales Dept.): (Service Dept.): E-Mail (all departments): & Commissioning,ġ. M 07/03/12 Updated to manufacturing version DA J 14/04/11 Changed logo and fax number RB I 29/11/07 Added system for this manual AL H 25/10/06 Added extra wall mounting option. Rev Date Revision Description Orig Check App Operation & Maintenance manual for FlatPack2
0 kommentar(er)
